Features for the
Scag SFC30
FULLY FABRICATED AND WELDED STEEL FRAME- MILITARY-GRADE STEEL – FRAME
Extra-strong, fully fabricated steel frame (not cast aluminum). The Military-Grade steel spec used on the SFC30 is over 200% stronger than standard drawing steel found in common stamped frames and decks in this machine class.
FULLY FABRICATED AND WELDED STEEL CUTTER DECK- MILITARY-GRADE STEEL – DECK
Extra-strong fabricated (non-stamped) steel cutter deck features 14-gauge, grade 100 Military-Grade steel deck shell, 12-gauge spindle reinforcement plate and ¼” side reinforcement bar, all while delivering the quality-of-cut you’d expect from a Scag mower.
POWERFUL TRANSMISSION & ENGINE COMBO- MAXIMUM POWER FOR TOUGH CUTS
The combination of a GT MV702 best-in-class transmission and Kohler CV224 engine bring the power for optimum performance in the toughest of cutting conditions.
DISCHARGE – MULCH – BAG- 3-IN-1 VERSATILITY
The SFC30 delivers the ability to discharge, mulch or bag. All options come as standard equipment, allowing the operator to change on the fly as needed. Discharge: discharge chute – Mulch: deck plug and mulch plate – Bag: bagging baffle, mulch plate and fabric bag
OVERSIZED ADJUSTABLE CONTROLS- ACHIEVE MAXIMUM COMFORT
Oversized handles feature internally routed cables to protect from potential snags. Handle features tool-free adjustment, up and down, to fit operator height preference. Additional vertical adjustment setting for transportation or storage.
OPERATOR CONTROL PANEL- ERGONOMIC CONTROLS
Angles of operator station controls match the natural angles of your outstretched hands. All controls are within easy reach: blade brake engagement, drive engagement, recoil start, throttle/choke, hour meter and park brake.
SCAG LEVEL QUALITY-OF-CUT- UNMATCHED PERFORMANCE
The large cutting chamber helps process more grass while being able to eat through wet and lush springtime grasses more efficiently. Cutter deck discharge opening is oversized for its class.
OFFSET BLADE SET UP- SIMPLIFIED DECK DRIVE SYSTEM
An offset blade design is less complex and easier to maintain than traditional timed deck setups. This more robust system results in potential belt replacements taking less than half the amount of time to repair/replace compared to timed deck systems. Image shown with bagging baffle.
SINGLE POINT HEIGHT-OF-CUT ADJUSTMENT- FINE-TUNED AND SIMPLE
Adjust the height-of-cut from a single location rather than at all four corners or having to adjust the front and back tires separately. Refine your height settings with adjustments from 1.5” to 5” in .25” increments.
Specifications
GENERAL
Total Fuel Capacity: 1 gallon
Rear Tires: 10.5" x 3" rubber tire w/ glass-filled polypropylene wheel
Front Tires: 9” x 2.25” rubber tire w/ glass-filled polypropylene wheel
DRIVE SYSTEM
Drive System Type: GT MV 702 Transmission
Forward Ground Speed: Up to 4 mph
Parking Brake: Hand lever
DECK
Cutting Widths: 30"
Type: Extra-strong, fully fabricated, and welded steel cutter deck. Offset blade, non-timed deck setup.
Cutting Height: 1.5" to 5" in .25" increments.
Blade Type: Optimized for maximum performance whether discharging, mulching, or bagging
Deck Lift: Hand lever. Single-point adjustment.
Construction: 14-gauge, grade 100, Military Grade steel deck shell with 12-gauge spindle reinforcement plate. ¼” trim side reinforcement bar offers extra protection against impacts.
Spindles: Aluminum housing with sealed ball bearings.
Blade Engagement: Blade brake clutch allows operator to disengage cutter blades without shutting off the machine.
Discharge, Mulch, Bag: Standard
Bag Capacity: 2.5 Bushels
WARNING:
This product may contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. For more information, go to www.P65Warnings.ca.gov.